Description
BOJ MODEL
S1+P+SRC (EN ISO 20345:2011) DIRECTIVE 89/686/CE. REGULATION UE 2016/425.
GENERAL DESCRIPTION:
Low perforated safety boot, padded collar, tongue, with double density polyurethane sole.
Design B according to EN ISO 20345: 2011. Manufacturing system by direct injection to the cut.
REQUIREMENTS MET:
Ergonomics and adjustment to the morphology of the user. Impact resistance (200 joules). Antistatic footwear.
Energy absorption in the heel. Puncture resistance. Resistance to hydrocarbons. Slip Resistance. Resistance to non-extreme environmental factors, under foreseeable conditions of use.
The constituent materials are suitable and do not affect the safety or health of the user. They do not cause risks or other nuisance factors under foreseeable conditions of use.
The constituent materials and the parts of the footwear that are in contact or may come into contact with the user who is wearing them do not have rough surfaces, sharp edges, points or protrusions that could cause injuries or excessive irritations. These materials or their decomposition products do not affect the safety and health of users.
The adjustment system cannot be accidentally misadjusted under foreseeable conditions of use; the adjustment and mismatch is done by means of cords, no tools being necessary.
The design facilitates its correct placement on the user, taking into account the environmental factors, the actions and postures to be carried out; the fit adapts to the wearer’s morphology including a variety of manufacturing sizes.
The footwear is designed to adapt to the natural perspiration of the foot and its absorption. The linings are designed to absorb sweat and perspiration.
The model meets the specific requirements to offer adequate protection against anticipated risks and withstand environmental factors under foreseeable conditions of use.
The date of manufacture is marked on the footwear (sole); The traceability of the batch is marked on the label of the cut and the label of the packing box (pair).
With anti perforation textile insole; Designation code S1 + P, complying with puncture resistance.
For models with P or S3 marking, the resistance to perforation of this footwear has been measured in the laboratory with a truncated nail of 4.5 mm in diameter, exerting a force of 1,100 N. If greater forces are applied or nails of smaller diameter, it will increase. the risk of perforation. In such circumstances, alternative preventive measures should be considered.
AVAILABLE SIZES: 35 – 48 EU
APLICATIONS:
Industry and construction. Maintenance and welding. Exterior and interior work. Warehouses Transport. Cleaning.
COMPONENT DESCRIPTION:
Blue split cowhide with a thickness of 2.0 – 2.2 mm.Tear resistance:> 120 N.
Tensile strength:> 20 N / mm2
Water vapor permeability:> 0.8 mg / cm2h.
Cr VI content: <3 ppm. pH:> 3.2
Water absorption:> 20% after 60 minutes.
Lining: Upper and Heel: in antiallergic polyamide based material, with great resistance to abrasion,
absorption and drying of perspiration.
Tear resistance:> 18 N.
Abrasion resistance:> 51,200 dry cycles and 25,600 wet cycles.
Water vapor permeability:> 2 mg / cm2h.
Tongue: Instep extension.
Padded collar with inner foam.
Non-woven fabric buttress impregnated with resins.
Inner insole made of foamed material with textile support, ergonomic design according to patternsbiomechanical gait.
Low density Antistatic Foamed Polyurethane midsole with high capacity forcushioning. Provides thermal insulation.
Compact Polyurethane outsole Antistatic, high density, biomechanical and non-slip design,
with anti-roll pads (anti-torsion system). Improves dynamic adaptation by at least 15%
with respect to the previous footwear (midfoot twist and goal twist). Provides greater absorption offorces in the impact phase and tread stability, tread uniformity and control ofpronation during walking.
Tear resistance:> 8 N / mm.Abrasion resistance: <150 mm3
Resistance to hydrocarbons: <12%
Hydrolysis resistance: <6 mm.Heel energy absorption:> 20 J.
Non-metallic toe cap, with impact resistance of 200 J; according to EN ISO standards20345: 2011 & EN ISO 12568: 2010, extra – wide last.
Anti-perforation textile insole with perforation resistance> 1,100 N.
Closure system with laces.
RISKS TO PROTECT:
Falling objects or crushing the ball of the foot: YES.
Falls and impact on the heel of the foot: YES.
Slip falls: YES.
Slipping on damp or greasy surfaces: YES.
Walking on pointed or sharp objects: YES. (Only models marked with P or S3).
Action and falling of objects on metatarsal: NO.
Finger injuries or foot deformities: YES.
Muscle fatigue produced by walking or standing: YES.
Works that cause vibrations: YES.
Blows in the ankle area: YES. (Does not meet the requirements for AN).
Possible sprains or strains of the ankle: YES.
Penetration of external materials: NO.
Accumulation of electrostatic charges generated by the movement or leaks of machinery of lowvoltage: YES.
Electrically Insulating Footwear: NO.
Electrically Conductive Footwear: NO.
Projection of molten metals: NO.
Possible burns and flames: NO. (Does not meet the requirements of EN 15090).
Heat from contact with hot surfaces: NO.
Very extreme heat conditions with a high need for perspiration: YES.
Cold exposure conditions (-10ºC): NO. Cold exposure conditions (-30ºC): NO.
Protection against dust or dirt: YES.
Protection against aggressive liquids: NO.
Water penetration through the instep due to sporadic or permanent exposure to humidity: NO.
Radiation protection: NO.
Protection against biological agents / bacteria: NO.
