MAYA (O2+CI+HRO+SRC)

76,06 IVA incluido

SKU: 90016 Categories: , ,

Ficha técnica →

Description

MAYA MODEL
O2+CI+HRO+SRC (EN ISO 20347:2012) DIRECTIVE 89/686/CE. REGULATION UE 2016/425.
GENERAL DESCRIPTION:
Professional trekking boot, padded collar, gusset and padded tongue, with polyurethane sole and antistatic nitrile rubber.
Design B, according to EN ISO 20347: 2012. Manufacturing system by direct injection to the cut.
REQUIREMENTS MET:
Ergonomics and adjustment to the morphology of the user. Antistatic footwear. Energy absorption in the heel.
Resistance to hydrocarbons. Resistance to water absorption and penetration. Cold insulation.
Contact heat resistance. Slip resistance. Resistance to non-extreme environmental factors, under foreseeable conditions of use.
The constituent materials are suitable and do not affect the safety or health of the user. They do not cause risks or other nuisance factors under foreseeable conditions of use.
The constituent materials and the parts of the footwear that are in contact or may come into contact with the user who is wearing them do not have rough surfaces, sharp edges, points or protrusions that could cause injuries or excessive irritations. These materials or their decomposition products do not affect the safety and health of users.
The adjustment system cannot be accidentally misadjusted under foreseeable conditions of use; the adjustment and mismatch is done by means of cords, no tools being necessary.
The design facilitates its correct placement on the user, taking into account the environmental factors, the actions and postures to be carried out; the fit adapts to the wearer’s morphology including a variety of manufacturing sizes.
The footwear is designed to adapt to the natural perspiration of the foot and its absorption. The linings are designed to absorb sweat and perspiration.
The model meets the specific requirements to offer adequate protection against anticipated risks and withstand environmental factors under foreseeable conditions of use.
The date of manufacture is marked on the footwear (sole); lot traceability isIt is marked on the cut label and the packing box label (pair).
Available with anti-perforation steel insole; Designation code O3, complying with puncture resistance.
For the models marked P, S3 and O3, the resistance to perforation of this footwear has been measured in the laboratory with a truncated nail of 4.5 mm in diameter, exerting a force of 1,100 N. If higher forces or nails of smaller diameter will increase the risk of perforation occurring. In such circumstances, alternative preventive measures should be considered.
AVAILABLE SIZES: 35 – 50 EU
APLICATIONS:
Industry and construction. Maintenance and welding. Exterior and interior work. WarehousesTransport. Cleaning. Agricultural labors.
COMPONENT DESCRIPTION:
Brown cowhide nubuck split leather with a thickness of 2.0 – 2.2 mm.Tear resistance:> 120 N.
Tensile strength:> 20 N / mm2
Water vapor permeability:> 0.8 mg / cm2h.
Cr VI content: <3 ppm. pH:> 3.2
Water absorption: <20% after 60 minutes.
Step and penetration: <0.2 gr in 60 minutes.
Neck and gusset: Gray split leather with a quality thickness of 1.2 – 1.4 mm.Tear resistance:> 30 N.
Tensile strength:> 20 N / mm2
Water vapor permeability:> 0.8 mg / cm2h.
Cr VI content: <3 ppm. pH:> 3.2
Water absorption:> 20% after 60 minutes.
Lining: Upper and Heel: in antiallergic polyamide based material, with great resistance to abrasion, absorption and drying of perspiration.
Tear resistance:> 18 N.
Abrasion resistance:> 51,200 dry cycles and 25,600 wet cycles.
Water vapor permeability:> 2 mg / cm2h.
Tongue: Instep extension.
Padded collar with inner foam.
Non-woven fabric buttress impregnated with resins.
Inner insole made of foamed material with textile support, ergonomic design according to patternsbiomechanical gait.
Low density Antistatic Foamed Polyurethane midsole with high capacity forcushioning. Provides thermal insulation.
Antistatic Nitrile Rubber sole, non-slip design. Gray anti-torsion pads that protrude from the sole and provide this effect. These properties are achieved by the design of the plant, which has a large contact surface, lug-type pads for soft soils, a brake area, and dirt and grease evacuation channels.
Tear resistance:> 8 N / mm.Abrasion resistance: <150 mm3
Resistance to hydrocarbons: <12%
Heel energy absorption:> 20 J.
Closure system with laces.
RISKS TO PROTECT:
Falling objects or crushing the ball of the foot: NO.
Falls and impact on the heel of the foot: YES.
Slip falls: YES.
Slipping on damp or greasy surfaces: YES.
Walking on pointed or sharp objects: NO. (Only models marked with P, O3 or S3).
Action and falling of objects on metatarsal: NO.
Finger injuries or foot deformities: YES.
Muscle fatigue produced by walking or standing: YES.
Works that cause vibrations: YES.
Blows in the ankle area: YES. (Does not meet the requirements for AN).
Possible sprains or strains of the ankle: YES.
Penetration of external materials: NO.
Accumulation of electrostatic charges generated by the movement or by leaks of low voltage machinery: YES.
Electrically Insulating Footwear: NO.
Electrically Conductive Footwear: NO.
Projection of molten metals: NO.
Possible burns and flames: NO. (Does not meet the requirements of EN 15090).
Heat from contact with hot surfaces: YES.
Very extreme heat conditions with a high need for perspiration: YES.
Cold exposure conditions (-10ºC): YES. Cold exposure conditions (-30ºC): NO.
Protection against dust or dirt: YES.
Protection against aggressive liquids: NO.
Water penetration through the instep due to sporadic or permanent exposure to humidity: NO.
Radiation protection: NO.
Protection against biological agents / bacteria: NO.

Additional information

Talla

35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50